MVT-7300 Owner's Guide
Based on the MVT-9000 Owner's Gude by Rich Wells, N2MCA
Modified by Mika, OH5HST
Bandercom, Inc. Technical Department
Introduction
In an effort to supply MVT-7300 owners with a better manual for their new
radios, this guide was written and based largely on the original MVT-9000
Owner's Guide written by Rich Wells, N2MCA. It was modified from its
original form by Mika, OH5HST, of Bandercom, Inc. and subsequently edited
by Rich Wells.This guide goes through the operation of the MVT-7300 in a step by step
process starting with the basics and builds up to the operation of the
more advanced features.Feel free to make copies of this document and distribute as you see
beneficial to the radio monitoring hobby. I simply ask that this information
be kept intact. A lot of hard work and effort has gone into the writing of
this guide. I would appreciate it if every effort is made to keep this
document whole with me as the original author.If you would like to share your thoughts about this owner's guide, have
suggestions for its improvement or have further questions, feel free to
send me e-mail.Happy reading and strong signals!
Rich Wells
N2MCA
n2mca@strongsignals.net
http://www.strongsignals.net/Mika
OH5HST
tech@bander.com
http://www.bander.com/tech
Table Of Contents
Warning
Features
Resources
Memory Organization
Definitions & Terms
Available Modes
Terminology
Mode Operations
VFO Mode
Memory Mode
Scanning Modes
Search Band Programming Mode
Searching Modes
Search Pass Mode
Priority Mode
Other Features
Attenuator
Battery Meter
Battery Saver
Beep
Clock
Cloning
Delay
Descrambler
Skip
Keylock
Lamp
Monitor
Power-on Resume
Reset
Skip
Features
1000 channels
500 search pass frequencies
10 memory banks
12 search bands (10 user programable)
16 step sizes
7 receive modes
1 priority channel
Large, full function, custom LCD
Duplex receive
Squelch monitor
Single VFO
Auto-store
Rotary control
Attenuator
Battery saver
Programmable lighting
Key locking feature
Programmable beep
Resources
1000 Memory channels (0-999)
500 Search pass frequencies
100 Channels/bank
10 Memory banks (1-10)
10 Search bands (0-9)
16 Step sizes (50/100 Hz
1/5/6.25/8/9/10/12.5/15/20/25/30/50/100/125 kHz)
7 Receive modes (AM/NAM/FM/WFM/USB/LSB/CW)
1 Priority channel
Memory Organization
Bank Channels Key
---- --------- ---
1 000 - 099 1
2 100 - 199 2
3 200 - 299 3
4 300 - 399 4
5 400 - 499 5
6 500 - 599 6
7 600 - 699 7
8 700 - 799 8
9 800 - 899 9
10 900 - 999 0
Definitions & Terms
Here are some basic definitions as well as terms used in the MVT-7300
Instruction Manual that will help you to use this guide more effectively.Attenuator
----------
A device which is used to diminish the strength of an incoming signal. This
is typically used to alleviate overloading of the front end radio circuitry
by very strong, and usually nearby, transmissions. The MVT-7300 allows you
to set the attenuator for individual memory channels as well as while
performing a search.Auto Mode/Step
--------------
This radio comes already programmed with regard to the recieve mode, step
size and duplex shift width that will be used dependent on the active
frequency. When you key in a frequency, the radio will automatically select
a receive mode and step size based on the range your frequency falls in. You
will likley find a number of ranges where this data is not correct due to
differences in national frequency bandplans.Duplex Shift
------------
A lot of radio systems use one frequency for transmitting and another for
receiving (usually the inputs and outputs to a repeater site). The
difference between these two frequencies is referred to as the duplex shift
width. The MVT-7300 uses a fixed shift width so that these two frequencies
can be monitored easily with a simple keypress.NOTICE: The current MVT-7300 uses a Japanese bandplan so the shift
width between the frequencies may not be correct for your
country.Memory Bank
-----------
An association of memory channels. This radio has 10 memory banks (0 - 9).
Since it also has 1000 memory channels, this means there are 100
memory channels per memory bank.Memory Channel
--------------
A location used to store a frequency and its associated settings such
as receive mode, attenuator, duplex width and alpha-tag. The MVT-7300
has 1000 memory channels which are divided into 10 banks.Pass
----
Refers to scanning and searching operations. A memory channel can be
passed so that it is not checked during a scan operation. A frequency
can be passed so it is not checked during a search operation. See Scan
Pass and Search Pass for more information.Priority Channel
----------------
A special memory channel that can be checked on a periodic basis for active
transmissions. This is usually programmed with very important frequency
that you do not want to miss activity on. The MVT-7300 has 1 priority
channel which is referred to as memory channel 1000.Receive Mode
------------
The method by which radio transmissions will be demodulated so that the
resultant audio portion may be directed to the speaker. Available receive
modes are:AM - Amplitude Modulation (below 30MHz, amateur radio, commercial
and military aircraft)
NAM - Narrow AM (mainly used below 25MHz)
FM - Frequency Modulation (most VHF/UHF communications)
WFM - Wide FM (for FM radio and TV audio)
USB - Upper Sideband (mainly used below 25MHz & amateur radio)
LSB - Lower Sideband (mainly used below 25MHz & amateur radio)
CW - Continuous Wave (amateur radio Morse code)Scan Pass
---------
Most receivers refer to this feature as channel lockout. Once a frequency
has been programmed into memory, a scanning operation will stop on this
channel if an active transmission is detected. Certain frequencies may
contain transmissions which are very or always active. To keep the
scanning operation from stopping on these channels, they can be locked-
out/skipped/passed during a scan.Scanning
--------
The act whereby memory channels are successively checked for active
radio transmissions of their programmed frequencies.Search Band
-----------
A feature which allows a pre-defined frequency range to be programmed so
that it can be repeatedly searched for active transmissions. Stored with
each search band are a starting frequency, ending frequency, receive mode
and step size. The MVT-7300 has 12 search bands. 10 of them are
user-programmable while the other 2 contain preprogrammed frequencies which
can not be altered.Search Pass
-----------
Some receivers refer to this feature as search-skip. If you have a known
frequency which you would like to skip while performing a search, it can
be placed in a special memory. Yupiteru refers to this as the Search
Pass Memory. Once placed in this memory, this frequency will not be tested
for an active transmission, or in other words it's skipped/passed when
performing a search. The MVT-7300 has 500 search pass frequencies.Searching
---------
The act whereby a frequency is incremented or decremented successively
to detect active radio transmissions in a given frequency range. Searching
is usually performed on a programmed Search Band.Skip
----
The MVT-7300 has a feature called Skip which allows a paused scan or search
to resume after a fixed time. Normally, during a scan or search, if an
active transmission is detected, the scanning or searching operation will be
paused until the transmission ceases. Once the transmission goes away, the
scanning or searching operation resumes. If you have the skip feature
enabled, scanning or searching will pause on an active transmission for at
most 4 seconds before resuming.Step Size
---------
A value in Hertz (Hz) or kiloHertz (kHz) that indicates the amount by which
a frequency will be changed due to user or radio control while searching
for active transmissions. Available step sizes are :
Notice! Step size depend mode.AM/NAM/FM: Auto step
1, 5, 6.25, 8, 9, 10, 12.5, 15, 20, 25, 30, 50, 100 kHz
WFM: Auto step
25, 50, 100, 125 kHz
USB/LSB/CW: Auto step
50, 100 Hz
1, 5, 6.25, 8, 9, 10, 12.5, 15, 20, 25, 30, 50, 100 kHzS-meter
-------
A feature used to graphically represent the strength of the signal being
received. It is usually calibrated to a dB (logarithmic) scale. A bar
graph is used where more bars indicate a stronger signal.VFO
---
A temporary location to store a frequency so that a memory channel does
not have to be programmed. Associated with this frequency are various
settings such as receive mode, step size, attenuator, etc. The MVT-7300
has a single VFO.
Available Modes
Memory
------
The radio is in Memory mode when a memory channel number is visible in the
upper left corner next to the CH indicator. Pressing the MR key toggles
between Memory and VFO modes.Priority
--------
Priority mode is enabled when the PRI indicator is visible. This is a mode
independent of the VFO, Memory, Scanning or Searching modes.Scanning
--------
In this mode, the scanning operation checks the specified banks for active
transmissions on the programmed frequencies within those banks. There are
two scanning modes with three scanning sub-modes for a total of six
different types of scan that can be performed.The 2 modes are:
Continuous : scanning of all non-empty banks
Bank : quick and dirty scanning of up to 4 banksThe 3 sub-modes are:
Normal : a normal scan
Mode : scans only those channels with the specified receive mode
Program : scans only those channels which have been program taggedThis gives us the following 6 scan mode types:
Continuous Normal
Continuous Mode
Continuous Program
Bank Normal
Bank Mode
Bank ProgramSearch Band Programming
-----------------------
In this mode, the search bands (1-10) used to perform searches are
programmed with starting and ending frequencies as well as step sizes
and receive modes.Searching
---------
In this mode, the searching operation checks for active transmissions on
the frequencies in the specified search range. There are two searching modes
and two searching sub-modes for a total of four different types of search to
be performed.The 2 modes are:
VFO : starts searching from the current VFO frequency
Band : search one of the programmed search bandsThe 2 sub-modes are:
Normal : a normal search
Auto-Store : stores active transmissions in Bank 10This gives us the following 4 search mode types:
VFO Normal
VFO Auto-Store
Band Normal
Band Auto-StoreThere is also a preprogrammed band search mode designed to search one of
the two factory preprogrammed search bands.Search Pass
-----------
The radio is in Search Pass mode when a blinking P indicator is visible
and the contents of the Search Pass memory are being displayed.VFO
---
The radio is in VFO mode when step size displayed. Pressing the MR key
toggles between VFO and Memory modes.
Terminology
When you see 'FUNC + key'
Press FUNC
You will hear a beep (if enabled) and FUNC will be displayed
Press 'key'
Mode Operations
---------------------------------------------------------------------------
VFO Mode
---------------------------------------------------------------------------The VFO can be programmed with
------------------------------
Frequency
Step size
Receive mode
Duplex mode
Priority channel
Attenuator
Delay
Beep
Battery saverHow to change the frequency
---------------------------
Simply key in the desired frequency
-----------------------------------
1. Enter the frequency
2. If you make a mistake during entry
A. Press C/AC
B. Use arrow keys to select digit to be corrected
C. Change digit using key press or rotary control
D. Press ENT when completed
3. Press ENTNote: Instead of correcting at step 2 above, simply press C/AC
twice and start over with the frequency entry.Use the rotary control or arrow keys
------------------------------------
Use the rotary control or arrow keys to increase or decrease the
currently displayed frequency by the currently set step size.
Holding down an arrow key will change the frequency rapidly.Use the ad-hoc approach
-----------------------
This approach allows you to change one or more of the individual
MHz digits of the current frequency. Press FUNC + MHz. Use the
arrow keys to select the digit to be changed (it will blink faster
than the other digits). Press the appropriate number key or use
the rotary control to select it. Repeat as necessary to change any
other digits. Press ENT to finish entry or C/AC to cancel the
changes.Regardless of how you change the frequency, be sure to verify the
receive mode and step size are set appropriately.Auto Mode
---------
If the AUTO indicator is visible, the radio will automatically
select the receive mode, step size and duplex shift width based on
the frequency. If you wish to change the receive mode and/or step
size, you must disable AUTO mode. Once AUTO mode is disabled (turned
off), the currently selected receive mode and step size will remain
regardless of what frequency is entered. To change the receive mode,
step size or AUTO setting, refer to the applicable instructions in
this section.Changing receive mode
---------------------
To disable Auto Mode
1. Press FUNC + MODE or just STEP
2. Use rotary control or arrow keys to select receive mode
3. Make sure AUTO is not visible
4. Press ENT to accept change or C/AC to cancelNote: Once AUTO MODE is disabled, the receive mode will remain
selected regardless of the frequency that is entered.To enable Auto Mode
1. Press FUNC + MODE or just STEP
2. Use rotary control or arrow keys to select receive mode until
AUTO is visible
3. Press ENT to accept change or C/AC to cancelNote: Once AUTO MODE is enabled, the receive mode will be
automatically selected based on the frequency that is
entered.Changing Step Size
------------------
To disable Auto Mode
1. Press STEP
2. Use rotary control or arrow keys to select step size
3. Make sure PRESET is not visible
4. Press ENT to accept change or C/AC to cancelNote: Once AUTO MODE is disabled, the step size will remain
selected regardless of the frequency that is entered.To enable Auto Mode
1. Press STEP
2. Use rotary control or arrow keys to select step size until
AUTO is visible
3. Press ENT to accept change or C/AC to cancelNote: Once AUTO MODE is enabled, the step size will be
automatically selected based on the frequency that is
entered.Duplex Shift
------------
The duplex shift function can be used onced the radio is placed in
duplex mode.Note: The duplex shift width is fixed is fixed and can not be altered.
Japanese model MVT-7300s will use widths based on the Japanese
radio bandplan which may use values which are not consistent
with the bandplan used in your country.To enable duplex shifting
1. Enable AUTO MODE for the desired VFO (see the sections for
Changing the Step Size and Receive Mode)
2. Press FUNC + DUPLEX
3. Note that DUP is displayed
4. To disable duplex shifting, press FUNC + DUPLEX (note DUP
disappears)To receive the duplex frequency
1. Make sure duplex mode is enabled by the presence of the DUP
indicator
2. To receive the duplex frequency, press and hold MONI
4. DUP will blink and the VFO frequency will be replaced by the
shifted frequencyProgramming Memory
------------------
Once a favorite frequency has been entered in VFO mode, it can be
programmed into one of the 1000 memory channels (0-999) or into the
priority channel (1000).When frequency data is copied from a VFO to a memory channel, a
specific channel number can be specified or the current memory
channel can be used.To copy to a specific memory channel
1. Enter the 3-digit channel number (0-999)
2. Press FUNC + MW
3. A double-beep is heardTo copy to the current memory channel
1. Press FUNC + MW
2. A double-beep is heardNote: The current memory channel can be noted by pressing MR to
enter Memory mode, noting the channel number, then pressing
MR to return to VFO mode.Note: When a VFO is copied to memory, the following settings are
also copied to that memory channel
1. Frequency
2. Step size
3. Receive mode
4. Attenuator settingEach time a memory write (copying VFO to memory) is performed, the
current memory channel is incremented by one. To write successive
memory channels, simply enter the frequency data and use the method
to copy this frequency to the current memory channel.When frequency data is copied from a VFO to a priority channel, the
specific channel number must be specified.To copy to a specific priority channel
1. Enter the 4-digit channel number (1000)
2. Press FUNC + MW
3. A double-beep is heardSearching
---------
Searching for new frequencies can be performed using the current VFO
frequency as a starting point. Refer to Searching Modes for further
details.---------------------------------------------------------------------------
Memory Mode
---------------------------------------------------------------------------
Memory mode is used to display the contents of memory which consists of
the normal 1000 memory channels and 1 priority channel. Memory mode can
be verified by the appearance of a single frequency and the channel
number in the upper-left corner.See the VFO Mode section for details on how memory channels are
programmed.Entering Memory Mode
--------------------
To enter Memory mode from VFO or Scan mode
1. Press MRTo enter Memory mode from Search mode
1. Press MR
2. Now in VFO mode
3. Press MRTo enter Memory mode from Search Pass mode
1. Press C/AC
2. Now in VFO mode
3. Press MRDisplaying Memory Channel Data
------------------------------
The 1000 memory channels have been broken down into 10 banks which
are labelled from 1-10. Each bank consists of 100 channels with
each starting at an even frequency (0, 100, 200, etc.).To move around within the memory channels
1. Use the rotary control or arrow keys
2. When the end of memory is reached in either direction, it will
simply wrap around to the other end and continueTo display a specific memory channel
1. Key in the 3-digit channel number (0-999)
2. Press MRNote: Memory channel 1000 is the priority channel
Displaying Priority Channel Data
--------------------------------
The Priority channel constitutes a single memory channel, 1000.To display the priority channel
1. Key in the 4-digit channel number (1000)
2. Press MRNote: The memory channels and priority channel have been separated so
that they do not become confused with each other. The rotary
control or arrow keys can not be used to move between them; it
will remain within the set of channels being displayed.Copying Memory Channel To VFO
-----------------------------
To copy a memory channel frequency and its settings to the VFO
1. Display the memory channel to be copied
2. Press FUNC + M>V
3. VFO mode will be displayed with a blinking frequency cursor
4. Use the rotary control or arrow keys to select the other VFO
5. Press ENT to copy or C/AC to cancelNote: The priority channel can not be copied to the VFO.
Copying A Memory Channel To Another
-----------------------------------
To copy the contents of one memory channel to another
1. Display the memory channel to be copied
2. Press FUNC + M.COPY
3. Memory bank information will be displayed
4. Use the rotary control or arrow keys to select the destination
memory bank
5. Press ENT to continue or C/AC to cancel
6. Memory channel information will be displayed
7. Use the rotary control or arrow keys to select the destination
memory channel
8. Press ENT to continue or C/AC to cancel
9. The new memory channel data will be displayed brieflyNote: Memory channels can not be copied to the priority channel and
vice versa.Erasing Memory Channel Data
---------------------------
Once a memory/priority channel has been programmed to memory, it is
easy to erase the channel contents.To erase the contents of a memory/priority channel
1. Display the desired channel
2. Press FUNC + MWReceiving Empty Channel Signals
-------------------------------
Due to the design of this receiver, if an empty memory channel is
being displayed, the radio circuitry will be trying to receive the
frequency of the last non-empty channel that was accessed. While
this causes no harm, it can be surprising when it occurs.Attenuator
----------
The attenuator setting for each memory channel can be changed at
any time. The current status can be view by looking for the ATT
indicator.To change the attenuator setting
1. Display the desired memory/priority channel
2. Press FUNC + ATTDuplex Shift
------------
The duplex shift function can be used onced the radio is placed in
duplex mode.Note: The duplex shift width is fixed is fixed and can not be
altered. Japanese model MVT-7300s will use widths based on
the Japanese radio bandplan which may use values which are
not consistent with the bandplan in your country.To enable duplex shifting
1. Press FUNC + DUPLEX
2. Note that DUP is displayedNote: When in Memory mode, duplex shifting is enabled or disabled
for all channels.To receive the duplex frequency
1. Select the desired memory channel
2. Make sure duplex mode is enabled by the presence of the DUP
indicator
3. To receive the duplex frequency, press and hold MONI
4. DUP will blink and the frequency will be replaced by the
shifted frequencyTo disable duplex shifting
1. Press FUNC + DUPLEX
2. Note that DUP disappearsScan Pass
---------
Associated with each memory channel is a setting which allows that
channel to be skipped during scan operations. This feature is called
scan pass and is covered in more detail under Scanning Modes.To set scan pass
----------------
1. Display the desired memory channel
2. Press FUNC + PASS
3. Note that CH blinksNote: The priority channel can not set scan pass.
To clear scan pass
------------------
1. Display the desired memory channel
2. Press FUNC + PASS
3. Note that CH does not blinkProgram Scan
------------
This feature allows up to ten channels in each bank to be specially
tagged so that they may be scanned separately from the rest of the
channels in that bank. This feature is called program scan and is
covered in more detail under Scanning Modes.To Tag A Memory Channel
-----------------------
1. Display the desired memory channel
2. Press FUNC + PGM
3. The PGM indicator appearsNote: The priority channel can not be program tagged.
To Untag A Memory Channel
-------------------------
1. Display the desired memory channel
2. Press FUNC + PGM
3. The PGM indicator disappears---------------------------------------------------------------------------
Scanning Modes
---------------------------------------------------------------------------
The MVT-7300 offers six different ways to scan the contents of memory.
There are two major and three minor modes of operation. By combining a
major mode with a minor mode, six different scanning types are
available.The 2 major modes are:
Continuous
----------
This mode allows for the scanning of every non-empty bank.
Bank
----
This mode allows for up to 4 specified banks to be scanned.The 3 minor modes are:
Normal
------
This mode simply scans all non-empty memory channels.
Mode
----
This mode scans memory channels with the specified receive
mode (AM/NAM/USB/LSB/CW/FM/WFM)
Program
-------
This mode scans memory channels which have been specially tagged.Scan Pass
---------
Regardless of the chosen scanning mode, channels that have been marked
as 'pass' will not be scanned. On most radios, this feature is
referred to as channel lockout.To Enable Channel Pass/lockout
------------------------------
1. Display the specified memory channel
2. Press FUNC + PASS
3. Note the CH indicator blinksTo Disable Channel Pass/lockout
-------------------------------
1. Display the specified memory channel
2. Press FUNC + PASS
3. Note the CH indicator does not blinkWhile Scanning
--------------
If the scan stops on a channel that you do not wish to have scanned
in the future, this channel can be passed by
1. Press FUNC + PASS
2. A double beep is sounded and the scan resumesChanging Scan Direction
-----------------------
All scanning modes start at the lowest applicable channel and work
towards the highest. To change the direction to scan from higest
to lowest once the scan has started, turn the rotary control in a
counter-clockwise direction or press the down/left arrow key. At
any time, the scaning direction can be reversed by simply using the
rotary control or arrow keys.Resuming Scanning
-----------------
If the scan stops on an active channel that you do not wish to
monitor, simply use the rotary control or arrow keys to resume
the scan.Cancelling Scan
---------------
To cancel a scan while it is running, simply press SCAN or MR.The Six Scanning Modes
----------------------Continuous Normal
-----------------
This mode is used to scan every programmed memory channel in every
bank. To start this mode
1. Press SCAN
2. The SCAN indicator appears and all scanned bank numbers
appear in display (0-9)Continuous Mode
---------------
This mode is used to scan every programmed memory channel in every
bank which has the specified receive mode. To start this mode
1. Press FUNC + M-SCAN
2. Receive mode will blink
3. Use rotary control or arrow keys to select receive mode
4. Press ENT
5. The SCAN indicator appears and receive mode blinksContinuous Program
------------------
This mode is used to scan every programmed memory channel in
every bank which has been specially tagged with the program
scan setting (PGM indicator). To start this mode
1. Press FUNC + P-SCAN
2. The SCAN indicator appears and PGM blinksBank Normal
-----------
This mode is used to scan up to 4 specified banks. To start this
mode
1. Specify up to four banks from 0-9 by pressing the appropriate
digit keys.
2. Press SCAN
3. The B-SCAN indicator appearsBank Mode
---------
This mode is used to scan the channels of up to four specified
banks which have the specified receive mode. To start this mode
1. Specify banks from 0-9 by pressing the appropriate
digit keys.
2. Press M-SCAN
3. Receive mode will blink
4. Use rotary control or arrow keys to select receive mode
5. Press ENT
6. The SCAN indicator appears and receive mode blinksBank Program
------------
This mode is used to scan every programmed memory channel which
has been specially tagged with the program scan setting (PGM
indicator) from up to four specified banks.To start this mode
1. Specify up to four banks from 0-9 by pressing the appropriate
digit keys.
2. Press FUNC + P-SCAN
3. The SCAN indicator appears and PGM blinksNote: The selected banks are always scanned in alphabetical
order (0-9) regardless of the order in which they
were entered.Attenuator
----------
The attenuator may be used during scanning to reduce signal strength.See Attenuator in the Other Features section for further details.
Delay
-----
The delay may be used during scanning to lengthen the scan resume
delay time from 2 to 4 seconds.See Delay in the Other Features section for further details.
Skip
-----
The skip feature may be used during scanning to make sure the scan
does not stay on any active frequency more than 4 seconds.See Skip in the Other Features section for further details.
---------------------------------------------------------------------------
Search Band Programming Mode
---------------------------------------------------------------------------
The MVT-7300 has 12 search bands (1-12) but only 10 of those are user
programable which are used to perform band searches.Before a band is used to perform a search, it should be programmed with a
starting and ending frequency as well as a step size and recieve mode to
be used during the search.To start this mode
1. Press FUNC + BW
2. Enter the starting search frequency (VFO freqency is used by
default)
3. Press ENT
4. Enter the ending search frequency
5. Press ENT
6. Enter bank where you want store the search 1-0 (11 & 12 are fixed
banks)
7. The radio beeps twice and returns to VFO mode---------------------------------------------------------------------------
Searching Modes
---------------------------------------------------------------------------
The MVT-7300 offers four different ways to search for active frequencies.
There are two major and two minor modes of operation. By combining a
major mode with a minor mode, four different search types are available.The two major modes are:
VFO
---
This mode allows for a search to be started from one of the
currently displayed VFO frequencies.
Band
----
This mode allows for up to four specified bands to be searched.The two minor modes are:
Normal
------
This mode performs a simply search which pauses when frequency
activity is detected so that you may listen.
Auto-Store
----------
This mode stores active frequencies into a predefined bank.Changing Search Direction
-------------------------
All search modes start at the designated starting frequency and
successively increment this frequency using the current step size
to try and find frequency activity. To reverse the direction of the
search at any time, simply turn the rotary control in a
counter-clockwise direction or press the down/left arrow key. At
any time, the search direction can be reversed by simply using the
rotary control or arrow keys.Resume Searching
----------------
If the search stops on an active frequency that you do not wish to
monitor, simply use the rotary control or arrow keys to resume
the search.Cancelling Search
-----------------
To cancel a search while it is running, simply press SRCH or MR.Auto-Store
----------
This mode performs a search and if activity is detected on a
frequency, that frequency is stored in bank j and the search
continues. You do not get to hear the audio from this frequency
activity because the radio pauses just long enough to store the
frequency and then resumes searching.Each time an Auto-Store search is started, the last 50 channels of
bank 0 (950 - 999) are erased. As active frequencies are found, there
will be a short pause as the radio stores the frequency in bank 0.Once the frequency is stored, there will be a beep and the radio will
then continue the search.During the search, should channels 950 - 999 become full, the search
will be aborted.The Four Searching Modes
-----------------------VFO Normal
----------
This mode is used to start a simple search from the VFO. Before
starting the search, be sure the frequency, step size and receive
mode are set appropriately. To start this mode
1. Press SRCH
2. The SRCH indicator appearsVFO Auto-Store
--------------
This mode is used to start a simple search from the current VFO
frequency and store active frequencies into bank j. Before starting
the search, be sure the frequency, step size and receive mode are
set appropriately. To start this mode
1. Press FUNC + AW SET
2. The SRCH indicator blinks informing Auto-Store is active
3. Press SRCHBand Normal
-----------
This mode is used to search up to 4 specified bands. To start this
mode
1. Specify up to four bands from 0-9 by pressing the appropriate
digit keys.
2. Press SRCH
3. The B-SRCH indicator appears along with programmed search
band settings.Band Auto-Store
---------------
This mode is used to search one specified band and store active
frequencies into memory channels 950 - 999. To start this mode
1. Press FUNC + AW SET
2. The SRCH indicator blinks informing Auto-Store is active
3. Specify the search band from 0-9 by pressing the appropriate
digit key
4. Press SRCH
5. The B-SRCH indicator blinks and programmed search band
settings are displayed.Preprogrammed Band Search
-------------------------
The MVT-7300 comes with bands 11 and 12 which are preprogrammed at
the factory and can not be changed. Band 11 is programmed with a large
number of business frequencies (which will most likely only be usable
in Japan) while band 12 is programmed with the 62 TV audio
frequencies.To start this mode
1. Press 11 or 12 to specify the band to be searched
2. Press SRCH
3. 'bus' will appear on the display if band 11 is searched while
the appropriate TV channel numbers will be displayed if band
12 is searched
4. Press SRCH to cancel the band searchAttenuator
----------
The attenuator may be used during a search to reduce signal strength.See Attenuator in the Other Features section for further details.
Delay
-----
The delay may be used during a search to lengthen the search resume
delay time from 2 to 4 seconds. This feature will have no function
if Auto-Store is enabled.See Delay in the Other Features section for further details.
Skip
----
The skip feature may be used during a search to make sure the search
does not stay on any active frequency more than 4 seconds. This
feature will have no function if Auto-Store is enabled.See Skip in the Other Features section for further details.
Search Pass
-----------
Regardless of the chosen search mode, frequencies that have been
marked as 'pass' will not be tested for activity. To read more about
this capability, see the Search Pass Mode section.---------------------------------------------------------------------------
Search Pass Mode
---------------------------------------------------------------------------
This mode allows you to display and edit the contents of the Search
Pass memory. This memory contains a list of frequencies which are to be
ignored when the radio is in one of the search modes. By doing so, this
allows you to skip over frequencies of known origin or those that are
active most/all of the time. Up to 500 frequencies can be entered into
this memory.To Put A Frequency In Search Pass Memory
----------------------------------------When in VFO mode
----------------
1. Tune the VFO to the desired frequency
2. Press FUNC + PASS
3. The P indicator will display briefly and two beeps will be
heardWhen in Search mode
-------------------
1. Make sure the radio has stopped on the desired frequency
2. Press FUNC + PASS
3. The P indicator will display briefly, two beeps will be
heard and the search will resumeTo Display Search Pass Memory
-----------------------------
1. Go to VFO mode
2. Press FUNC + S.P.READ
3. The step size will be replaced with a flashing P indicator while
the frequency cursor points to a frequency in the list
4. Use the rotary control or arrow keys to display any remaining
frequencies in the memory.Note: If there are no frequencies stored in memory, the message
"Error" will be displayed briefly and the radio will remain in
VFO mode.
Note: The frequencies are stored in this memory in numerical order
making it easier to find a known frequency.
Note: Signals can be received on the frequency while it is being
displayed.To Remove A Frequency
---------------------
1. Display the desired frequency
2. Press FUNC + PASS
3. Two beeps will be heard and the next frequency will be displayedNote: When the last frequency has been removed, the message "Error"
will be displayed briefly and the radio will return to VFO mode.To Exit From Search Pass Memory
-------------------------------
Press C/AC or FUNC + SPR---------------------------------------------------------------------------
Priority Mode
---------------------------------------------------------------------------
The MVT-7300 can be programmed with one priority channel which, when
priority is enabled, will be checked every five seconds for activity. The
priority channel is actually an extension of the 1000 memory channels and
is referred to as memory channel 1000.Programming The Priority Channel
--------------------------------
1. Go to VFO mode
2. Tune the desired frequency and receive mode
3. Enter the 4-digit priority channel number (1000)
4. Press FUNC + MW
5. The channel number 1000 is briefly displayed then
the radio returns to VFO modeDisplaying Priority Channel Data
--------------------------------
The Priority channel is actually memory channel 1000 so simply key
in 1000 followed by MR.Erasing Priority Channel Data
-----------------------------
Once a priority channel has been programmed to memory, it is easy to
erase the channel contents.1. Display the priority channel
2. Press FUNC + MWEnabling Priority Mode
----------------------
Once the desired priority channel has been programmed, it is now
ready to be checked for activity.Note: Once priority mode is enabled, you can then go to VFO, Memory,
Scan or Search mode and the priority channels will continue
to be checked every five seconds.Disabling Priority Mode
-----------------------
To disable priority mode
1. Press FUNC + PRI
2. The PRI indicator disappearsAttenuator
----------
The attenuator setting for priority channel can be changed at
any time. The current status can be view by looking for the ATT
indicator.To change the attenuator setting
1. Display the priority channel
2. Press FUNC + ATTScan Pass
---------
The priority channel can not be passed.
Other Features
---------------------------------------------------------------------------
Attenuator
---------------------------------------------------------------------------
If the radio is used in an area where excessively strong signals are
active, it may be necessary to reduce their strength to ensure that
the radio receiver functions properly. The Attenuator is used to
reduce the strength of all signals entering into the receiver.Signals which enter the radio and are too powerful for it to handle,
may result in various forms of interference. Such signals may effect
frequencies to either side or can even desensitize the receiver so
that it may not be able to receive signals it normally can.To enable the Attenuator
1. Press FUNC + ATT
2. The ATT indicator appearsTo disable the Attenuator
1. Press FUNC + ATT
2. The ATT indicator disappearsBoth VFOs have their own attenuator setting. Each memory channel can
be individually programmed with an attenuator setting. After a search
operation is started, the Attenuator can be enabled or disabled as is
deemed necessary.---------------------------------------------------------------------------
Battery Meter
---------------------------------------------------------------------------
The Battery Meter is used to give a graphical indication of the power
remaining in the batteries. It is located in the upper right corner of
the LCD and looks like a battery lying on its side.When new or freshly charged batteries are put in the radio, both bars
inside the battery icon should be visible. As the battery power depletes,
one bar, then the other will disappear. The batteries will then need to
be replaced soon.If the battery icon begins to flash, that means the power level is
dangerously low and the radio is close to turning itself off. Replace
the batteries immediately should this occur.---------------------------------------------------------------------------
Battery Saver
---------------------------------------------------------------------------
To extend the operating time of the radio, the Battery Saver feature is
used. Not only can this feature be enabled or disabled upon request,
the amount of time the saver circuitry is active can be selected.To enable the Battery Saver
1. Press FUNC + SAVE
2. The SAVE indicator appearsTo disable the Battery Saver
1. Press FUNC + SAVE
2. The SAVE indicator disappearsThe Battery Saver is only effective when used in VFO or Memory modes.
If no transmission is detected on the displayed frequency within five
seconds, the Battery Saver is engaged.Once engaged, the Battery Saver puts the radio "to sleep" for a period
of time, then "wakes up" briefly to check for an active transmission.
The amount of time the radio spends "sleeping" can be selected. While
the radio is "asleep", power usage is lowered thus saving battery
power. The longer the sleep time, the more power is saved and the
longer the batteries will last.To select the sleep time
1. Press the digit key corresponding to the desired sleep time
1 = 0.3 seconds
2 = 0.9 seconds
3 = 1.5 seconds
2. Press FUNC + SAVE
3. The SAVE indicator appearsNote: The sleep time is set to 0.3 seconds when shipped from the factory.
---------------------------------------------------------------------------
Beep
---------------------------------------------------------------------------
The MVT-7300 sounds a beep tone each time a key is pressed. This helps
to provide audible feedback during radio operations. Shipped from the
factory, the beep tone is enabled which can be verified by the presence
of the BEEP indicator. For more discreet operations, it may be necessary
to disable this feature.To disable the beep tone
1. Press FUNC + BEEP
2. The BEEP indicator disappearsTo enable the beep tone
1. Press FUNC + BEEP
2. The BEEP indicator appearsNote: The volume of the beep corresponds to the setting of the Volume
control.---------------------------------------------------------------------------
Clock
---------------------------------------------------------------------------
The MVT-7300 comes with a time of day clock which can be used as a
reference as well as setting an alarm or indicating when the radio is
to turn on or off by itself.To set the clock
1. Go to VFO mode
2. Press FUNC + SET
3. Use the rotary control until 'CL' appears in the upper left corner
of the display
4. Press ENT
5. Use the rotary control to set the hour
6. Press ENT
7. Use the rotary control to set the minute
8. Press ENT
9. The radio beeps twice and returns to the previous modeWhen the MVT-7300 is powered off, it will display the current time on the
LCD. When the radio is on, the current time can be displayed as well.To view the current time
1. Go to VFO mode
2. Press ENT
3. The current time is displayed for 5 seconds
4. The display returns to VFO modeNote: During step 3, the radio can be forced back to VFO mode before the
5 seconds expires by simply pressing ENT.To set the alarm time
1. Go to VFO mode
2. Press FUNC + SET
3. Use the rotary control until 'AL' appears in the upper left corner
of the display
4. Press ENT
5. Use the rotary control until 'On' appears
6. Press ENT
7. Use the rotary control to set the hour
8. Press ENT
9. Use the rotary control to set the minute
10. Press ENT
11. The radio beeps twice and returns to the previous modeNote: When the alarm goes off a series 2 double beeps will be
heard.
Note: To help ensure you hear the alarm beeps, be sure to set the
Volume control sufficiently highTo disable the alarm
1. Go to VFO mode
2. Press FUNC + SET
3. Use the rotary control until 'AL' appears in the upper left corner
of the display
4. Press ENT
5. Use the rotary control until 'OFF' appears
6. Press ENT
7. The radio beeps twice and returns to the previous modeTo set the turn on time
1. Go to VFO mode
2. Press FUNC + SET
3. Use the rotary control until 'On' appears in the upper left corner
of the display
4. Press ENT
5. Use the rotary control until 'On' appears
6. Press ENT
7. Use the rotary control to set the hour
8. Press ENT
9. Use the rotary control to set the minute
10. Press ENT
11. The radio beeps twice and returns to the previous mode
12. Tune the VFO or select the appropriate memory channel to the
station you want to hear when the radio turns on
13. Press and hold PWR to turn the radio off
14. TIMER appears in the lower right corner of the LCDTo disable the turn on time
1. Go to VFO mode
2. Press FUNC + SET
3. Use the rotary control until 'On' appears in the upper left corner
of the display
4. Press ENT
5. Use the rotary control until 'OFF' appears
6. Press ENT
7. The radio beeps twice and returns to the previous modeTo set the turn off time
1. Go to VFO mode
2. Press FUNC + SET
3. Use the rotary control until 'OFF' appears in the upper left corner
of the display
4. Press ENT
5. Use the rotary control until 'On' appears
6. Press ENT
7. Use the rotary control to select the number of minutes until
the radio should turn itself off
8. Press ENT
9. The radio beeps twice and returns to the previous mode
10. Timer appears in the lower right corner of the LCD
11. The radio will turn itself off after the specified timeTo disable the turn off time
1. Go to VFO mode
2. Press FUNC + SET
3. Use the rotary control until 'OFF' appears in the upper left corner
of the display
4. Press ENT
5. Use the rotary control until 'OFF' appears
6. Press ENT
7. The radio beeps twice and returns to the previous mode
8. TIMER no longer appears in the lower right corner of the LCD---------------------------------------------------------------------------
Cloning
---------------------------------------------------------------------------
Cloning is used to transfer all of the data and settings from one
MVT-7300 into another. This makes it easy for one owner to easily share
their radio setup with another. It can also be used by dealers to set up
the radios they sell for customers upon request.In the procedure that follows, the MVT-7300 which will be sending its
data to the other MVT-7300 will be called the Master. The MVT-7300 which
receives the programming data from the master is called the Slave.To Clone the contents of the Master to the Slave
1. Connect the Master to the Slave using a cable with 3.5mm plugs on
both ends and connected to the EAR jack of each unit
2. Turn on both the Master and Slave
3. Set both Master and Slave to VFO mode
4. On both radios
A. Press 9998
B. Press FUNC + C/AC
5. 'Pc Int' should be displayed on the LCDs
6. On the Slave unit, press 6 then ENT. This puts it into a state
waiting to receive the cloning data
7. On the Master unit, press 1 then ENT. This starts the sending of
cloning data
8. Both LCDs will update with memory addresses as data is transferredWARNING: While data is being transferred, DO NOT press any keys on
either unit, DO NOT try to turn the radios off and DO NOT
unplug the cable from either end!Note: This data transfer operation will take several minutes.
9. When the Master unit is done sending, its display will return to
'Pc Int'
10. When the Slave unit is done receiving, it will turn itself off
and the display will show 'CLEAr' for one second. If there is an
error in the transfer, the display will show 'Error' and then
return to 'Pc Int' (if this happens start the entire procedure
over)
11. Turn off the Master unit
12. Disconnect the cable from both EAR jacks---------------------------------------------------------------------------
Delay
---------------------------------------------------------------------------
During a scan or search operation, after a transmission ends, there will
be a two second delay before the scan/search is resumed. This delay
allows for a response to be heard. To increase this delay time to four
seconds, the Delay function is used.To enable Delay
1. Press FUNC + DELAY
2. The DLY indicator appearsTo disable Delay
1. Press FUNC + DELAY
2. The DLY indicator disappears---------------------------------------------------------------------------
Descrambler
---------------------------------------------------------------------------
The MVT-7300 comes with descrambler circuitry which can be used to
unscramble voice inverted transmissions used on some cordless phones
and law enforcement radios.To enable the descrambler
1. Press SCR
2. The audio characteristics of a received signal should changeNote: The descrambler can only be enabled on FM signals
Note: Try this on a non-scrambled transmission to note the change
in audio as well as to find out what a voice inverted signal
sounds like.To disable the descrambler
1. Press SCRTo adjust the descrambler inversion point
1. Enable the descrambler
2. Rotate the DIAL in both directions to try and find
the most understandable audio---------------------------------------------------------------------------
Keylock
---------------------------------------------------------------------------
The MVT-7300 comes with a keylock which can be used to make sure that
accidental key or control activations do not effect the radio.To enable the keylock
1. Press FUNC + LOCK
2. The key indicator appears in the upper right cornerNote: Once the keylock is enabled, only the PWR, LAMP, MONI, FUNC
and LOCK keys can be used.To disable the keylock
1. Press FUNC + LOCK
2. The key indicator is no longer displayed---------------------------------------------------------------------------
Lamp
---------------------------------------------------------------------------
The MVT-7300 contains a brilliant backlighting system which is used to
illuminate both the display and keypad for nighttime operations. While
the keypad always uses a green backlight, the display backlight can be
changed between green and orange.To set single five-second illumination (factory default)
1. Press LAMP
2. The LAMP indicator is not displayedTo set constant illumination
1. Press and hold LAMP until the LAMP indicator appears
2. Press LAMP to turn offTo change illumination colour
1. Press FUNC + LAMP
2. The Display illumination changes to the opposite colorNote: Excessive use of the Lamp feature will dramitically reduce the
operational time of the radio when batteries are being used.---------------------------------------------------------------------------
Monitor
---------------------------------------------------------------------------
The MONI button on the side of the radio is used for several purposes.
Normally, pressing it immediately opens the squelch. This allows for
checking transmissions whose strengths might be below the squelch
threshhold or for monitoring weak signals which are fading in and out
resulting in repetitive squelch operations.When the duplex function is enabled in VFO mode, MONI is used to receive
the duplex shift frequency.---------------------------------------------------------------------------
Power-on Resume
---------------------------------------------------------------------------
This built-in functionality allows the MVT-7300 to continue doing what
it was doing when it was powered off, in some instances. Scanning
operations will not be resumed but will leave the radio in Memory
Mode on the last accessed channel.If the radio was searching when it was turned on, upon power-on, it will
enter Search Pause mode. Simply press SRCH to resume the search.
The settings regarding Bandscope and Priority mode will be rememberd so
that they can be set appropriately upon power-on.---------------------------------------------------------------------------
Reset
---------------------------------------------------------------------------
If the MVT-7300 should behave oddly or if you wish to clear the entire
contents of memory to start "fresh," the radio can be reset.WARNING: Resetting the MVT-7300 will erase all memory contents, return
all settings to their default values, and reprogram all the
search bands to their factory settings!To reset the radio
1. Turn the radio off
2. Press and hold 7 and ENT keys
3. Turn radio on
4. CLEAr will appear on the LCD for a few seconds
5. Release keys---------------------------------------------------------------------------
Skip
---------------------------------------------------------------------------
The Skip function is used during scan and search modes to prevent the
radio from stopping on any one frequency for an undue amount of time.Normally, when scanning or searching comes across an active transmission
it will stop on that frequency until the transmission ceases and then
resume scanning/searching. For some situations, staying on one frequency
for too long may miss transmissions occuring on other frequencies.When the Skip function is enabled, if the scan or search operation
stops on an active transmission, it will resume the scan/search when
the transmission ends or four seconds have elapsed; whichever occurs
first.To enable Skip
1. Press FUNC + SKIP
2. The SKIP indicator appearsTo disable Skip
1. Press FUNC + SKIP
2. The SKIP indicator disappears
Last updated August 3, 2000
Copyright 2000 by Richard J. Wells & Mikan TechModified for MVT-7300 June 19, 2000
Mika, OH5HST
Bandercom, Inc. Technical Department